home about us products upcoming events links contact inquiries distribution      
>Inderm PSI
Features
Instructions
Specifications
Example Drops
Volume per Injection
Inderm Basic Plus
Features
Instructions
Specifications
Volume per Injection
Inderm Nappage NEW!
Features
Instructions
Specifications
Accessories


More Information
Mesotherapy
Fat Transfer

_______________________

CONTACT INFO:
TEL: 949.458.1897
FAX: 949.458.7416
EMAIL:
info@indermpsi.com

MAILING ADDRESS:
4 AUTRY, SUITE B
IRVINE, CALIFORNIA 92618
U.S.A.

______________________



Inderm PSI: Instructions

 
Installing the Syringe

Standard B-D Luer-Lock ® syringes (1, 3, 5, or 10 ml/cc) are recommended for use with the Inderm-PSI device. To install the syringe, lift open the door of the syringe driver and slide it as far back as is needed to clear the syringe. Next, point the tip of the needle into the guard carefully and then drop the syringe plunger into the appropriate slot of the driver. Slide the syringe forward until it is fully seated against the cradle and tighten the syringe cradle knob. DO NOT OVER TIGHTEN THE SYRINGE CRADLE KNOB. The needle should not protrude beyond the needle guard. There is a syringe stop located in the cradle to prevent the syringe from sliding forward even if the knob is loose. Close the door of the driver to secure the syringe. The device will not operate unless the door of the syringe driver is closed. Verify that the syringe and needle are purged of air before starting injections.
 
Selecting the Function

To turn the Inderm PSI ™ on, press and hold the power button for 3 seconds and the power light will glow indicating that the device is on. Once the power is on, there is no default function on the device. When the activation button is pressed, nothing will happen until operating parameters are selected.
 
Deactivating the Needle Guard

** The device can be activated by either pressing the activation button or pressing the needle guard into the device. If you wish, you may deactivate the needle guard by turning the device on and before selecting any parameters, press and hold the activation button for 10 seconds. The device will beep when you initially press the activation button, continue to press the activation button for 10 seconds until the device beeps a second time. The device will now only be activated by pressing the activation button. To reset the system, to allow for the activation of the device using the needle guard, you must turn the device off, turn it back on, and press and hold the activation button for 10 seconds. Again, the device will beep when you initially press the activation button, continue to press the activation button for 10 seconds until the device beeps a second time.
 
Forward and Reverse Modes

The Forward and Reverse buttons are located to the right of the power button. To select either the forward or reverse mode, push either button until a beep occurs. When the forward button is pressed, the device will beep once to indicate in forward mode. When the reverse button is pressed, the device will beep twice to indicate in reverse mode. In reverse mode, only the continuous mode may be used, the C indicator light will flash and syringe size selections and volume selections will be deactivated.
 
Syringe Size and Volume Selection

The syringe size and volume size must be selected, as shown, before trigger activation occurs. Press and hold the syringe selection button until the correct syringe size is chosen. Next, press and hold the volume selection button until the correct volume is chosen. With the syringe and the volume selected the device will deliver the volumes shown below. Also view the example drops.
 

Volume per Injection
  Volume Selection
Syringe Size 0.01 0.02 0.05 0.08 0.10

1 ml

0.001
0.0002
0.005
0.008
0.01
3 ml
0.003
0.006
0.015
0.024
0.03
5 ml
0.005
0.01
0.025
0.04
0.05
10 ml
0.01
0.02
0.05
0.08
0.10

* Total volume is based on the size of the syringe selected.
In Continuous mode it is recommended that the Inderm be pulsed with short pauses to alleviate pressure buildup in the syringe.
Verify that the syringe and needle are purged of air before starting injections.
User testing is recommended to verify the volume is adequate for the intended use.
(When using a 10ml syringe, volumes .08 and .10 will only work in slow mode)


Special 10X Mode
:

*Only available in slow mode for the 10 ml syringe and with the .02, .05, and .10 Volume selection.*
To use the 10X mode:
1.  Set the speed to slow
2.  Set the syringe size to 10ml
3.  Select the volume, .02, .05, or .10 (10X mode is only available for volumes .02, .05, and .10).
4.  Press the forward and reverse buttons simultaneously for about 1.5 seconds, until the device starts beeping.
5.  After the device beeps, release the forward and reverse buttons.
6.  The indicator of the volume selected (.02, .05, or .10) will be flashing.
7.  The device is now in the 10X mode and will deliver 10 times the volume selected.
The following volumes will be delivered when the unit is set to the 10X mode:

Volume per Injection 10X mode

  Volume Selection
Syringe Size 0.02 0.05 0.10
10 ml
0.2
0.5
0.10

IF YOU REQUIRE SPECIAL PROGRAMMING,
WE MAY CUSTOMIZE THE 'VOLUME PER INJECTION'
TO YOUR EXACT SPECIFICATIONS.

*Call IMI for details*

Injecting Doses

The Inderm is programmed to signal when the injection is completed. The signal is a single beep that follows every injection. This signal is used to allow time for the injection to be absorbed.
   
  page: 1 2
 
 
HOME     ABOUT US      PRODUCTS    UPCOMING EVENTS      LINKS      CONTACT US     INQUIRIES      DISTRIBUTION    TERMS & CONDITIONS

Copyright © 2005-2008 Innovative Med Inc. All rights reserved.